Search found 139 matches

by G.Lang
Tue 30. Aug 2016, 09:13
Forum: Software
Topic: PEAK PCAN-USB+ Insite Cummins_RP1210A
Replies: 4
Views: 9738

Re: PEAK PCAN-USB+ Insite Cummins_RP1210A

Hello Sergio, please download the SysInfo tool from the following URL -> http://www.peak-system.com/produktcd/Tools/PEAK%20System%20Information/PeakSysInfo.exe Start the *.EXE (no installation required), let the analysis run and save the result as a XML file, send the XML file to info@peak-system.co...
by G.Lang
Thu 25. Aug 2016, 16:04
Forum: PCAN-MicroMod
Topic: Scale & offset values in Micromod configuration Sw
Replies: 12
Views: 7683

Re: Scale & offset values in Micromod configuration Sw

Hello Lauren, the possible values for scale and offset are decimal values between -65535 and 65536 micromod_values.JPG Below an example for a 50Hz PWM Output with scale =1 (note: the logic is inverted because it´s a lowside driver) 8Bit PWM Out -> 0..100% FFh = 255 = 0% 00h = 0 = 100% 3Fh = 63 = 75%...
by G.Lang
Mon 22. Aug 2016, 10:43
Forum: PCAN-USB Pro
Topic: This device cannot start. (Code 10)
Replies: 0
Views: 151911

This device cannot start. (Code 10)

If you are using a PCAN-USB FD or a PCAN-USB Pro FD at Windows 10 and you have trouble with the driver installation please follow the steps below: -> Plug the PCAN-USB Pro FD into the affected USB port from your computer where the error warning appear. -> Go to the device manager (control panel) and...
by G.Lang
Thu 9. Jun 2016, 11:28
Forum: PCAN-USB Pro
Topic: Driver not digitally signed -> (Code52)
Replies: 1
Views: 217500

Driver not digitally signed -> (Code52)

Since driver version 4.1 our drivers use the new microsoft driver model with a new signature and therefore it´s necessary to update the certificate store otherwise you get the "Code 52" warning at Win Vista/7 and 8.x driver4_1_x.JPG Solution 1: Update your system or Solution 2: Download driver versi...
by G.Lang
Wed 16. Mar 2016, 09:29
Forum: PCAN-MicroMod Evaluation Kit
Topic: Increase output voltage
Replies: 5
Views: 13131

Re: Increase output voltage

Hello,

sorry but this is not possible.

best regards
Gunther
by G.Lang
Mon 14. Mar 2016, 13:14
Forum: PCAN-MicroMod Evaluation Kit
Topic: Increase output voltage
Replies: 5
Views: 13131

Re: Increase output voltage

Hello,

all MicroMod boards use the same µC, that´s correct but the motherboards differ.
Note: The PCAN-MicroMod Evalboard don´t have any analogue outputs.

best regards
Gunther
by G.Lang
Mon 14. Mar 2016, 10:58
Forum: PCAN-MicroMod Evaluation Kit
Topic: Increase output voltage
Replies: 5
Views: 13131

Re: Increase output voltage

Hello,

the PCAN-MicroMod Evaluationboard don´t have any analogue outputs, sorry.

BTW: A scale of 4000 at the MicroMod Analog 2 output is more like a "digital output" than an anlogue output.

best regards
Gunther
by G.Lang
Wed 2. Mar 2016, 14:41
Forum: PCAN-Ethernet Gateway DR
Topic: Signal delay due to CAN/ENET Gateway
Replies: 4
Views: 5177

Re: Signal delay due to CAN/ENET Gateway

Hi, please update the firmware to version 2.5.1 Below some screenshots with disabled "tcpdelay", in this configuration i use a PCAN-PCI card connected to the PCAN-Ethernet-Gateways CAN channel 1 at the one side and a PCAN-Virtual Gateway on the other side (see "Communication between Gateway and PC v...
by G.Lang
Tue 1. Mar 2016, 15:00
Forum: PCAN-Ethernet Gateway DR
Topic: Signal delay due to CAN/ENET Gateway
Replies: 4
Views: 5177

Re: Signal delay due to CAN/ENET Gateway

Hello, the gateway itself has an internal delay <1ms, but if you are using the TCP protocol there is a additional delay called "tcpdelay" active (=default) You can´t switch off this "tcpdelay" in the GUI, please export the configuration, open the "poi_config.ini" with a text editor and set "tcpdelay...
by G.Lang
Fri 26. Feb 2016, 08:40
Forum: Linux
Topic: ISO-TP impemetation for data extension
Replies: 1
Views: 1431

Re: ISO-TP impemetation for data extension

Hello,

there is no ISO-TP implementation for Linux available from PEAK, maybe there exist such a implementation at the socketcan website -> GitHub

best regards
Gunther