Error testing CAN FD frames PEAK CAN USB X6 Device
-
- Posts: 7
- Joined: Tue 20. Jun 2017, 12:01
Re: Error testing CAN FD frames PEAK CAN USB X6 Device
Hi stephane,
yes, immediately after sending CAN FD Frame ( cansend can0 123##1DEADBEEFDEADBEEF) and listening on the other interface( candump can1 ) leads to error in transmission with Red led's blinking
below is the results of the command you said:
yes, immediately after sending CAN FD Frame ( cansend can0 123##1DEADBEEFDEADBEEF) and listening on the other interface( candump can1 ) leads to error in transmission with Red led's blinking
below is the results of the command you said:
Re: Error testing CAN FD frames PEAK CAN USB X6 Device
Hi,
please check the used CAN cables. Looks like the termination resistors are missing on boths ends. Then it could work with lower bitrates, but won´t work with higher bitrates or FD.
regards
Michael
please check the used CAN cables. Looks like the termination resistors are missing on boths ends. Then it could work with lower bitrates, but won´t work with higher bitrates or FD.
regards
Michael
-
- Posts: 7
- Joined: Tue 20. Jun 2017, 12:01
Re: Error testing CAN FD frames PEAK CAN USB X6 Device
Hi Michael,
Thanks a lot for the information.
Everything works fine after adding termination resistors in the CAN cable.
Regards,
Jibin
Thanks a lot for the information.
Everything works fine after adding termination resistors in the CAN cable.
Regards,
Jibin
Re: Error testing CAN FD frames PEAK CAN USB X6 Device
Hi jibinkurian1246,
Did you use 2 different terminals for cansend and candump?
Why i am asking is even i face the same issue what you faced, i have set the correct baudrate for my CANFD, after sending message via cansend, i dont see any traffic over any channel with candump command.
another thing i want to know about the connections, from my board i have 3 DB9 connectors out of which one i use for power supply, how do i use the other 2 connectors so that i can see my CAN traffic on candump.
I am new to CAN and Linux platform
Thanks for the useful info on this page.
Did you use 2 different terminals for cansend and candump?
Why i am asking is even i face the same issue what you faced, i have set the correct baudrate for my CANFD, after sending message via cansend, i dont see any traffic over any channel with candump command.
another thing i want to know about the connections, from my board i have 3 DB9 connectors out of which one i use for power supply, how do i use the other 2 connectors so that i can see my CAN traffic on candump.
I am new to CAN and Linux platform
Thanks for the useful info on this page.
Re: Error testing CAN FD frames PEAK CAN USB X6 Device
Hi Prasad,
which CAN hardware from PEAK do you use? Please post output of "ip link ls" and "cat /proc/pcan"
regards
Michael
which CAN hardware from PEAK do you use? Please post output of "ip link ls" and "cat /proc/pcan"
regards
Michael
Re: Error testing CAN FD frames PEAK CAN USB X6 Device
Hello Maidhof,
Thanks for the reply. Please find the below screen shot for "ip link ls"
Please let me know if we need to use 2 terminals? If yes, i am using minicom, i am i able to open 2 terminals?
Thanks for the reply. Please find the below screen shot for "ip link ls"
Please let me know if we need to use 2 terminals? If yes, i am using minicom, i am i able to open 2 terminals?
Re: Error testing CAN FD frames PEAK CAN USB X6 Device
Please find the same here
Re: Error testing CAN FD frames PEAK CAN USB X6 Device
Hi,
please answer all my questions:
Michael
please answer all my questions:
regardswhich CAN hardware from PEAK do you use? Please post output of "ip link ls" and "cat /proc/pcan"
Michael
Re: Error testing CAN FD frames PEAK CAN USB X6 Device
Hi,
Sorry for missing your questions.
Unfortunately i am not using any PEAK related CAN board, as the questions are generic i am trying to get some info from this thread so that it helps me
Sorry for missing your questions.
Unfortunately i am not using any PEAK related CAN board, as the questions are generic i am trying to get some info from this thread so that it helps me
Re: Error testing CAN FD frames PEAK CAN USB X6 Device
Hi,
well...this is a PEAK-System Forum, where we discuss all issues related to PEAK products. So I don't think that you will get an answers for your problem with your board. But if you want to have a working system, you can use one of our PCAN products and connect it to your board
regards
Michael
well...this is a PEAK-System Forum, where we discuss all issues related to PEAK products. So I don't think that you will get an answers for your problem with your board. But if you want to have a working system, you can use one of our PCAN products and connect it to your board

regards
Michael