Search found 139 matches

by G.Lang
Fri 4. Oct 2019, 11:32
Forum: PCAN-USB FD
Topic: CAN FD work do not work IDs bigger then 7FF
Replies: 1
Views: 1030

Re: CAN FD work do not work IDs bigger then 7FF

Hi,

please use both message types

#define PCAN_MESSAGE_EXTENDED 0x02U // The PCAN message is a CAN Extended Frame (29-bit identifier)
#define PCAN_MESSAGE_FD 0x04U // The PCAN message represents a FD frame in terms of CiA Specs
pcanbasic_help.png
pcanbasic_help.png (90 KiB) Viewed 1025 times
regards
Gunther
by G.Lang
Fri 31. May 2019, 11:01
Forum: PCAN-LIN
Topic: Reading LIN information in Chevrolet car
Replies: 1
Views: 916

Re: Reading LIN information in Chevrolet car

Hi Brian,

we don´t know the LIN bit rate of your GM car. LIN is a little different than CAN, you must also set the correct LIN format, the matching bit length and "Subscriber" as direction. Please also take care that the "Forward Mask" is set to RS-232.
LIN.JPG
LIN.JPG (174.78 KiB) Viewed 906 times
regards
Gunther
by G.Lang
Wed 8. May 2019, 13:48
Forum: PCAN-MicroMod Motherboards
Topic: PWM Ausgang konfigurieren
Replies: 6
Views: 1592

Re: PWM Ausgang konfigurieren

Hallo, bei dem "PWM + Frequency Output" handelt es sich bei der MicroMod Mix2 um die analogen Ausgänge AOut 0 und AOut 1. pwm_out.JPG Output 0 beim "PWM + Frequency Output" ist der 0...10V Spannungsausgang AOut 0 Output 2 beim "PWM + Frequency Output" ist der 0...20mA Stromausgang AOut 1 Mit freundl...
by G.Lang
Tue 7. May 2019, 08:50
Forum: PCAN-MicroMod Motherboards
Topic: PWM Ausgang konfigurieren
Replies: 6
Views: 1592

Re: PWM Ausgang konfigurieren

Hallo, beim digitalen Output 0 handelt es sich um einen "Low-side"-Ausgang, er gibt also keine Spannung heraus, er schaltet gegen GND. Der digitale Ausgang Output 7 schaltet nur die LED "Dout 7" und ist nicht extra herausgeführt. Nur der digitale Ausgang Dout 0 ist an den Anschlüssen herausgeführt (...
by G.Lang
Thu 20. Dec 2018, 14:09
Forum: PCAN-MIO
Topic: Configure a switch signal (0V or 5V) output for PCAN-MIO
Replies: 1
Views: 1169

Re: Configure a switch signal (0V or 5V) output for PCAN-MIO

Hi Yousif, i can´t really understand your problem, exercise 2e shows the necessary steps mio_example.JPG Please follow the exercises 2a, 2b and 2e and it will work, all steps are explained. Should we send you the matching PCAN-MIO configuration? I´m not really willing to do this because it look that...
by G.Lang
Tue 31. Jul 2018, 15:14
Forum: PCAN-PCI Express
Topic: Fixed channel assignment with PCAN-PCIexpress
Replies: 4
Views: 10704

Re: Fixed channel assignment with PCAN-PCIexpress

Updated list for parameter 2 (CAN_GetDriverName) PCI and PCIexpress based cards 0x101 = PCAN-PCI 0x101 = PCAN-PCI Express (the Tundra powered version, sold till ~2014) 0x103 = PCAN-PCI Express (current version) 0x113 = PCAN-PCI Express FD 0x101 = PCAN-PC/104-Express (the Tundra powered version, sold...
by G.Lang
Tue 31. Jul 2018, 15:07
Forum: Hardware
Topic: Fixed device ID/channel assignment with PCAN-USB
Replies: 3
Views: 25357

Re: Fixed device ID/channel assignment with PCAN-USB

Updated list for parameter 2 (CAN_GetDriverName) PCI and PCIexpress based cards 0x101 = PCAN-PCI 0x101 = PCAN-PCI Express (the Tundra powered version, sold till ~2014) 0x103 = PCAN-PCI Express (current version) 0x113 = PCAN-PCI Express FD 0x101 = PCAN-PC/104-Express (the Tundra powered version, sol...
by G.Lang
Mon 16. Jul 2018, 10:59
Forum: PCAN-Basic
Topic: Not working PC even copy PCANBasic.dll
Replies: 7
Views: 2251

Re: Not working PC even copy PCANBasic.dll

Hi,

don't affront our customers and any different nations.
Thanks for understanding.

Gunther
by G.Lang
Mon 4. Jun 2018, 16:56
Forum: PCAN-Explorer 5 & Add-ins
Topic: Hardware Already In Use Error
Replies: 1
Views: 980

Re: Hardware Already In Use Error

Hi,

please post a screenshot of the PCAN-Explorer tool "PCAN Status Display".

best regards
Gunther
by G.Lang
Fri 1. Jun 2018, 14:36
Forum: PCAN-USB FD
Topic: Why is a there a constant high bus load?
Replies: 4
Views: 2912

Re: Why is a there a constant high bus load?

Hi Daniel, thanks for your request. It looks you are a CAN newbie :-) Please take a look at the following topic in our forum to understand what´s "wrong", especially the question from "Lukast85" and the answer from K.Wagner https://www.peak-system.com/forum/viewtopic.php?f=41&t=74&p=5230&hilit=Bushe...